# ABB Robot Fault Codes \(IRC5 & OmniCore\): Alarm List & Recovery Guide

> Troubleshoot ABB IRC5 and OmniCore fault codes 10010, 20010, 38200 SMB battery, 50056 collision, 50204 motion supervision, and 71058 PROFINET loss.

Canonical: https://roboticsengineering.in/abb-robot-fault-codes-irc5-omnicore-troubleshooting/ | Published: 2026-11-20 | Updated: 2026-11-20

ABB IRC5 / OmniCore · OEM Fault Hub

## ABB Robot Fault Codes (IRC5 & OmniCore): Alarm List & Recovery Guide

Instant filter for ABB RobotWare event logs, SMB battery & revolution counter updates, motion supervision trips, and PROFINET recovery.

Instant Filter (Code, Alarm Name, or Symptom)

Showing 10 of 10 ABB OEM fault codes

ABB · 10010 **Motors Off State / Guard Stop**

Safety/I-O

**Root Cause:** Controller entered Motors Off due to Auto Stop, General Stop, or safety chain interruption.

**Recovery Steps:** Close cell gates, verify AS1/AS2 and GS1/GS2 LEDs on safety board, then press Motors On pushbutton.

**Safety Interlock:** Verify dual-channel safety integrity if fault repeats.

ABB · 20010 **Emergency Stop Reset Required**

Critical E-Stop

**Root Cause:** Emergency stop circuit was opened and subsequently closed, awaiting explicit reset.

**Recovery Steps:** Confirm E-stop buttons are released and press Reset / Motors On button on FlexPendant or cabinet.

**Safety Interlock:** Never auto-reset E-stop without physical inspection.

ABB · 20201 **Limit Switch / Axis Overtravel**

Motion/Collision

**Root Cause:** Joint exceeded configured software or hardware travel limit during jog or program move.

**Recovery Steps:** Jog axis back inside software limits using joint coordinate mode; inspect hard stops if triggered.

**Safety Interlock:** Check workobject frame offsets if occurring in AUTO.

ABB · 38200 **SMB Battery Charge Low**

Servo/Drive

**Root Cause:** Serial Measurement Board (SMB) lithium backup battery voltage dropped near warning threshold.

**Recovery Steps:** Order and replace SMB battery inside manipulator base with power ON, then verify revolution counters.

**Safety Interlock:** Update revolution counters immediately if power was lost while depleted.

ABB · 50050 **Position Out of Reach**

Motion/Collision

**Root Cause:** Target RobTarget lies outside kinematic reach or wrist singularity envelope.

**Recovery Steps:** Adjust target coordinates, ConfL/ConfJ configuration flags, or base/tool frame definition.

**Safety Interlock:** Simulate modified path in T1 low speed first.

ABB · 50056 **Joint Collision / Torque Supervision**

Motion/Collision

**Root Cause:** Estimated external torque exceeded motion supervision threshold on one or more axes.

**Recovery Steps:** Clear physical obstruction, inspect part weight vs LoadData, and recalibrate LoadIdentify if tooling changed.

**Safety Interlock:** Inspect gearbox backlash after hard stops.

ABB · 50204 **Motion Supervision Triggered**

Motion/Collision

**Root Cause:** High acceleration against heavy inertia or sudden contact caused drive torque trip.

**Recovery Steps:** Verify accurate mass and center-of-gravity in tool0/tooldata and reduce AccSet ramp if needed.

**Safety Interlock:** Check gripper mounting bolts for shear or loosening.

ABB · 50296 **Drive Unit DC Link Undervoltage**

Servo/Drive

**Root Cause:** Mains phase drop, blown rectifier fuse, or loose contactor on DC bus distribution.

**Recovery Steps:** Measure L1-L2-L3 mains voltage under load and check main contactor K1/K2 coil and contacts.

**Safety Interlock:** Follow lockout-tagout and capacitor discharge wait time.

ABB · 50357 **Corner Path Failure**

Motion/Collision

**Root Cause:** Program pointer could not compute zone blend ahead due to WaitDI/logic blocking Lookahead.

**Recovery Steps:** Adjust zone data (z10/z50) or insert WaitTime/InPos synchronization before I/O reads.

**Safety Interlock:** Verify clearance around blend corner before increasing zone radius.

ABB · 71058 **PROFINET / Fieldbus I/O Comm Lost**

Safety/I-O

**Root Cause:** PLC fieldbus cable unplugged, IP conflict, or switch port link drop interrupting cyclic I/O.

**Recovery Steps:** Inspect RJ45/M12 patch cord, check PLC Device Name & GSDML status, and warm-restart I/O bus.

**Safety Interlock:** Ensure safe outputs fail to de-energized state on bus loss.

### ABB IRC5 / OmniCore SMB Battery & Revolution Counter Update

1. When Event 38200 (SMB Battery Low) appears, replace the 3.6V/7.2V lithium SMB battery inside the robot base while controller power remains ON.
2. Switch controller to Manual Mode (<250 mm/s), hold the FlexPendant enabling device, and jog all axes to their mechanical calibration marks.
3. On FlexPendant tap ABB Menu -> Calibration -> ROB_1 -> Rev. Counters -> Update Revolution Counters.
4. Confirm all 6 axes match zero within mark tolerances and run a slow verification check in Manual Full Speed before AUTO production.

`<iframe src="https://roboticsengineering.in/abb-robot-fault-codes-irc5-omnicore-troubleshooting/" width="100%" height="780" style="border:1px solid #d6dfeb;border-radius:12px;" loading="lazy" title="ABB Robot Fault Codes (IRC5 & OmniCore): Alarm List & Recovery Guide"></iframe>`

**Grow Your Robotics / Automation Brand Online with Jaadu Digital** Technical SEO, B2B lead generation, and engineering content systems built for robotics integrators and OEMs.

[Explore Jaadu Digital →](https://jaadudigital.com/)

### Frequently Asked Engineering Questions

**How do I fix ABB Event 50204 Motion Supervision Triggered?**

Run ABB LoadIdentify in Manual mode so tooldata and loaddata accurately reflect EOAT mass, center of gravity, and inertia, and inspect dress packs for mechanical binding.

**What happens if ABB Event 38200 SMB battery dies while powered off?**

The Serial Measurement Board loses multi-turn revolution counts. Replace the SMB battery, jog each axis to calibration witness marks, and execute Update Revolution Counters on the FlexPendant.

**How do I troubleshoot ABB 71058 PROFINET Fieldbus I/O communication loss?**

Inspect M12/RJ45 Ethernet cabling, verify the controller PROFINET Device Name matches the PLC TIA Portal / GSDML hardware configuration, and warm-restart the controller.

Multi-Currency · INR ₹ · USD $ · EUR €

## Cobot vs 6-Axis Industrial Robot ROI & Payback Calculator

Cobot Payback: 19.3 mo

Currency & Region Preset

Operators Replaced per Shift

Shifts per Day (1–3)

Fully Loaded Cost / Operator / Year

Cobot Cell Turnkey CapEx

6-Axis Industrial Cell CapEx (incl. Fencing)

Annual Throughput / Scrap-Reduction Value

6-Axis High-Speed Cycle Bonus (%)

Annual Maintenance & Power (% of CapEx)

Cobot Payback

19.3 mo

6-Axis Ind. Payback

43.5 mo

Cobot 5-Yr Net Gain

₹41,12,500

6-Axis 5-Yr Net Gain

₹16,62,500

**5-Year Cumulative Net Value Comparison**

Collaborative Robot (Cobot)₹41,12,500

6-Axis Industrial Robot Cell₹16,62,500

**Engineering Takeaway:** At 2 shifts/day, the Cobot achieves faster capital recovery due to lower safety guarding and integration overhead.

`<iframe src="https://roboticsengineering.in/cobot-vs-industrial-robot-roi-calculator/" width="100%" height="780" style="border:1px solid #d6dfeb;border-radius:12px;" loading="lazy" title="Cobot vs Industrial Robot ROI Calculator"></iframe>`

**Grow Your Robotics / Automation Brand Online with Jaadu Digital** Technical SEO, B2B lead generation, and engineering content systems built for robotics integrators and OEMs.

[Explore Jaadu Digital →](https://jaadudigital.com/)

### Frequently Asked Engineering Questions

**What is a realistic robotics ROI payback period in Indian manufacturing?**

On 2-shift CNC machine tending or palletizing, cobots typically pay back in 14–24 months while caged 6-axis industrial cells pay back in 24–42 months depending on throughput uplift.

**Why does a 6-axis industrial cell cost more up front than a cobot?**

Beyond the manipulator price, industrial cells require safety fencing, dual-channel light curtains, safety PLCs, heavier floor pedestals, and specialized integrator commissioning.

**When does a 6-axis industrial robot beat a cobot on 5-year ROI?**

When cycle times are aggressive (<5 s), payloads exceed 20–30 kg, or 24/7 3-shift operation amplifies the 25–45% throughput advantage of high-speed industrial arms.

**What annual OpEx percentage should be budgeted for robot cells?**

Budget 4–6% of total cell CapEx annually for grease/oil PM kits, gripper wear pads, vision lens cleaning, backup batteries, and electrical power (~0.6–2.5 kW average).

**How should fully loaded operator cost be calculated?**

Include base wages plus statutory benefits (PF/ESI/insurance), shift allowances, overtime, training, and attrition overhead rather than take-home pay alone.
