# ESP32-C3: RISC-V 160 MHz, Wi-Fi, Bluetooth 5 LE, 5 µA deep sleep

> The single-core RISC-V Espressif ESP32-C3 chip for small battery robots and sensors: CPU, memory, GPIOs, peripherals and sleep current.

Canonical: https://roboticsengineering.in/components/esp32-c3-soc/ | Published: 2026-11-03 | Updated: 2026-11-03

**The ESP32-C3 is a single-core 32-bit RISC-V microcontroller running up to 160 MHz with 2.4 GHz Wi-Fi, Bluetooth 5 (LE), 400 KB of SRAM and a deep-sleep consumption of 5 µA.** It is the small, low-cost chip in the family, with fewer pins than the [ESP32-S3](https://roboticsengineering.in/components/esp32-s3-soc/). Figures are from the Espressif ESP32-C3 Series datasheet, version 2.4.

## Key specifications

| CPU | RISC-V single-core, up to 160 MHz |
| --- | --- |
| Wireless | Wi-Fi 802.11b/g/n, Bluetooth 5 (LE) |
| SRAM | 400 KB |
| GPIOs | 22 (16 on some variants) |
| ADC | two 12-bit, up to 6 channels |
| Deep sleep | 5 µA |

## What the datasheet promises

| Item | Datasheet value |
| --- | --- |
| Processor | 32-bit RISC-V single core, up to 160 MHz; 483.27 CoreMark |
| Wireless | 2.4 GHz Wi-Fi (802.11b/g/n) and Bluetooth 5 (LE) |
| Memory | 384 KB ROM, 400 KB SRAM (16 KB for cache), 8 KB RTC SRAM; optional in-package flash up to 8 MB |
| GPIOs | 22 on the standard chip; 16 on the ESP32-C3FH4X and FH4AZ; 3 strapping pins |
| Serial and bus | Two UARTs, three SPI, I2C, I2S, TWAI (CAN 2.0) controller, full-speed USB Serial/JTAG |
| PWM and timing | LED PWM up to 6 channels; remote-control peripheral; two 54-bit timers |
| Analog | Two 12-bit SAR ADCs, up to 6 channels; temperature sensor |
| Power | Deep-sleep consumption 5 µA, with RTC memory kept powered |
| Security | Secure boot, flash encryption, AES, SHA, RSA and a random number generator |
| Package | QFN32, 5 × 5 mm |

With 22 GPIOs and six ADC channels the C3 suits a simple robot controller or sensor node rather than a camera robot; for that, use the S3. Check the board’s documentation for which pins are broken out.

## Using it on a robot

- Use it for battery-powered sensors that wake, read and sleep, using the 5 µA deep-sleep mode.
- Drive a small motor driver with the LED PWM channels, or a CAN transceiver from the TWAI controller.
- Keep the three strapping pins in mind when you wire the first pins.
- For a dual-core chip with more pins, use the [ESP32-S3](https://roboticsengineering.in/components/esp32-s3-soc/).

## Sources and further reading

- [Espressif ESP32-C3 Series datasheet (v2.4)](https://documentation.espressif.com/esp32-c3_datasheet_en.pdf) — processor, wireless, memory, GPIOs, peripherals and sleep current above.

Last reviewed: November 2026. Limits are from the Espressif datasheet for the chip; development boards add their own regulator, USB chip and pin choices. No price is quoted because it has not been checked.
