# ESP32-S3: dual-core 240 MHz, Wi-Fi, Bluetooth 5 LE, 45 GPIOs

> The Espressif ESP32-S3 chip behind many camera and display robot boards: cores, memory, peripherals and wireless, from the datasheet.

Canonical: https://roboticsengineering.in/components/esp32-s3-soc/ | Published: 2026-11-03 | Updated: 2026-11-03

**The ESP32-S3 is a dual-core Xtensa LX7 microcontroller running up to 240 MHz with 2.4 GHz Wi-Fi, Bluetooth 5 (LE), 512 KB of SRAM and 45 programmable GPIOs.** It adds a camera interface, an LCD interface and full-speed USB OTG over the older chip on the [ESP32 DevKit V1](https://roboticsengineering.in/components/esp32-devkit-v1/). Figures are from the Espressif ESP32-S3 Series datasheet, version 2.2.

## Key specifications

| CPU | dual-core Xtensa LX7, up to 240 MHz |
| --- | --- |
| Wireless | Wi-Fi 802.11b/g/n, Bluetooth 5 (LE) |
| SRAM | 512 KB |
| GPIOs | 45 |
| USB | full-speed OTG |
| Camera | 8–16-bit DVP interface |
| ADC | two 12-bit, up to 20 channels |

## What the datasheet promises

| Item | Datasheet value |
| --- | --- |
| Processor | Dual-core 32-bit Xtensa LX7, up to 240 MHz; 1329.92 CoreMark with both cores |
| Wireless | 2.4 GHz Wi-Fi (IEEE 802.11b/g/n) and Bluetooth 5 (LE) |
| Memory | 384 KB ROM, 512 KB SRAM, 16 KB RTC SRAM; optional in-package flash and PSRAM |
| GPIOs | 45 programmable, 4 of them strapping pins; some are used by in-package flash or PSRAM |
| Serial and bus | Three UARTs, two I2C, two I2S, SPI ports, TWAI (CAN 2.0) controller, SD/MMC host with 2 slots |
| USB | Full-speed USB OTG and a USB Serial/JTAG controller |
| Display and camera | LCD interface and an 8 to 16-bit DVP camera interface |
| Motor and timing | LED PWM up to 8 channels, two MCPWM, RMT, pulse counter |
| Analog | Two 12-bit SAR ADCs, up to 20 channels; 14 touch-sensing pins; temperature sensor |
| Package | QFN56, 7 × 7 mm |

The chip is sold in variants with different in-package flash and PSRAM, listed in the datasheet’s ordering table. Development boards choose their own variant and pin layout, so check the board’s documentation for which GPIOs are free.

## Using it on a robot

- Use it where a robot needs a camera and Wi-Fi together, or a display, with USB handled by the chip itself.
- Use the MCPWM and LED PWM channels for motor drivers, and the TWAI controller for a CAN bus.
- Avoid the strapping pins for loads that would pull them at reset, and the pins used by in-package memory.
- For a smaller, cheaper chip with Wi-Fi and Bluetooth LE, see the [ESP32-C3](https://roboticsengineering.in/components/esp32-c3-soc/).

## Sources and further reading

- [Espressif ESP32-S3 Series datasheet (v2.2)](https://documentation.espressif.com/esp32-s3_datasheet_en.pdf) — processor, wireless, memory, peripherals and package above.

Last reviewed: November 2026. Limits are from the Espressif datasheet for the chip; development boards add their own regulator, USB chip and pin choices. No price is quoted because it has not been checked.
