# External ADC for Robot Sensors: ADS1115 or ADS1015?

> ADS1115 or ADS1015 for robot sensors: resolution, sample rate, gain ranges and step sizes worked out.

Canonical: https://roboticsengineering.in/external-adc-ads1115-vs-ads1015/ | Published: 2026-11-07 | Updated: 2026-11-07 | Author: Jignesh S Panchal

**Choose the ADS1115 when you need fine resolution from slow sensors such as thermistors, load cells or battery dividers, and the ADS1015 when you need a faster sample rate and 12 bits is enough.** Both are 4-channel I2C converters with a programmable gain amplifier, so the main trade is resolution against speed.

## Key takeaways

- The ADS1115 is a 16-bit converter and the ADS1015 is a 12-bit converter, and the ADS1115 resolves 16 times finer steps.
- The ADS1015 samples much faster than the ADS1115; datasheet-class figures are in the thousands of samples per second against under a thousand.
- Both have 4 single-ended inputs or 2 differential pairs and a gain setting that changes the full-scale range.
- An input must stay within the supply limits, so a 3.3 V board needs a lower range or a divider.

## Resolution Bits

Resolution is the smallest voltage step the converter can report. The ADS1115 and ADS1015 both output a signed result, so one bit is the sign, leaving 15 bits (ADS1115) or 11 bits (ADS1015) for positive voltages.

The step size, called one LSB, is the full-scale range divided by the number of positive codes. With the 4.096 V range selected, the ADS1115 gives 4.096 / 32768 = 0.000125 V, which is 0.125 mV per step. The ADS1015 gives 4.096 / 2048 = 0.002 V, which is 2 mV per step. For comparison, an Arduino Uno 10-bit input on a 5 V reference gives 5 / 1024 = 4.88 mV per step. The ADC resolution bits explained article covers the idea in more depth. Remember that noise often hides the lowest bits, so more bits do not always mean a more accurate reading.

## Sample Rate

Sample rate is how many readings per second the converter can take. The ADS1015 is the faster one, and the ADS1115 is slower in exchange for its extra bits.

Commonly listed figures are 8 to 860 samples per second for the ADS1115 and 128 to 3300 samples per second for the ADS1015, but check your datasheet. Both also have a single-shot mode and a continuous mode. If you read four channels in turn, divide the rate by four, and add time for changing the multiplexer. For a battery voltage or a temperature, a few readings a second are plenty. For a fast current signal or a vibration, 860 samples per second may be too slow and a 12-bit ADS1015 or a microcontroller’s own fast ADC may suit better.

## Input Channels

Both chips have four analogue input pins. You can use them as four single-ended inputs measured against ground, or as two differential inputs that measure the voltage between two pins.

Differential mode helps when the signal sits on top of a common voltage, for example reading across a shunt resistor, as in the [DC power meter with ACS712](https://roboticsengineering.in/projects/dc-power-meter-acs712-arduino/), or reading a bridge sensor. The I2C address is set by an address pin and gives four possible addresses, so you can place up to four chips on one bus. That is 16 single-ended channels. If your microcontroller already has few free pins, see the [ESP32 pinout for robotics](https://roboticsengineering.in/esp32-pinout-for-robotics/), where some ADC pins stop working while Wi-Fi is active and an external ADC avoids the problem. For a general look at the bus itself, read [I2C, SPI and UART for robotics](https://roboticsengineering.in/i2c-spi-uart-robotics/).

## Gain Settings

Gain here sets the full-scale input range, and a smaller range gives finer steps. The programmable gain amplifier offers six ranges: 6.144 V, 4.096 V, 2.048 V, 1.024 V, 0.512 V and 0.256 V.

Never rely on the range to protect the pin. The input voltage must stay within the supply limits given in the datasheet, which is roughly from ground to the supply plus a small margin, so the 6.144 V range does not let you feed 6 V into a chip powered at 3.3 V. The table below shows the step size for each range, calculated as range divided by 32768 for the ADS1115 and by 2048 for the ADS1015.

| Full-scale range | ADS1115 step | ADS1015 step |
| --- | --- | --- |
| 6.144 V | 187.5 uV | 3 mV |
| 4.096 V | 125 uV | 2 mV |
| 2.048 V | 62.5 uV | 1 mV |
| 1.024 V | 31.25 uV | 0.5 mV |
| 0.512 V | 15.625 uV | 0.25 mV |
| 0.256 V | 7.8125 uV | 0.125 mV |

Worked example with an LM35 temperature sensor, which outputs 10 mV per degree Celsius. Assume the 2.048 V range. The ADS1115 step of 62.5 uV equals 0.0625 mV, so 0.0625 / 10 = 0.00625 degrees Celsius per step. The ADS1015 step of 1 mV gives 1 / 10 = 0.1 degrees per step. The Uno at 4.88 mV gives 4.88 / 10 = 0.488 degrees per step. The finer step does not make the sensor itself more accurate, only the reading finer.

## Cost and Availability

Both parts are sold on breakout boards by many Indian electronics shops and online marketplaces, so availability is rarely the issue. Prices change often, so check current listings rather than trusting a number in an article.

The ADS1015 usually costs a little less, and the difference rarely matters for one board. Look at the seller’s listing for the exact chip marking, the I2C pull-up resistors on the board and whether the pins are soldered. Counterfeit or mislabelled boards exist, so a quick scan and a known-voltage test on arrival is worth the five minutes. The component pages for the [ADS1115 ADC](https://roboticsengineering.in/components/ads1115-adc/) and the [ADS1015 12-bit ADC](https://roboticsengineering.in/components/ads1015-12-bit-adc/) list what to check on each board.

## Which Fits Your Sensors

Match the converter to how fast the signal changes and how small the change you care about is. Slow signals with small steps favour the ADS1115, and quick signals that need only coarse steps favour the ADS1015.

For a battery monitor using a resistor divider, as in the [battery voltage monitor with divider](https://roboticsengineering.in/projects/battery-voltage-monitor-divider-arduino/), the ADS1115 gives a smooth reading from a signal that changes slowly. For several analogue sensors on a robot that you read many times a second, the ADS1015 may leave more time for your control loop. Whichever you pick, average several readings, and the [sensor filtering with moving average and median](https://roboticsengineering.in/arduino-sensor-filtering-moving-average-median/) guide shows how. To size a divider for your own voltage, use the [LED resistor and voltage divider calculator](https://roboticsengineering.in/led-resistor-voltage-divider-calculator/). More background lives in the [Learn hub](https://roboticsengineering.in/learn/).

## How to check this yourself

1. Connect the breakout to your board, run an I2C scanner and note the address, which is usually `0x48` with the address pin to ground.
2. Feed a known steady voltage, such as the 3.3 V pin through a divider, and read it at two different gain settings.
3. Measure the same voltage with a multimeter and compute the difference between the two readings.
4. Short the input to ground and log 100 readings, then look at how many codes the value wanders across. That is your real noise floor.
5. Change the data-rate setting and repeat step 4 to see how noise changes with speed.

## Common mistakes

- Picking the 6.144 V range and applying more than the supply allows on the input pin.
- Expecting 16 bits to give 16-bit accuracy when noise, reference and sensor error dominate.
- Forgetting that the maximum sample rate is shared across channels.
- Leaving the address pin floating, which gives an unreliable address.

## Quick checklist

- Pick the ADS1115 for fine steps on slow signals and the ADS1015 for speed.
- Choose the lowest gain range that still covers your sensor voltage.
- Keep every input within the supply limits from the datasheet.
- Average several readings to reduce noise.
- Scan the I2C address on arrival and check against a multimeter.

## Frequently asked questions

### What is the difference between ADS1115 and ADS1015?

The ADS1115 is a 16-bit converter with a slower maximum rate, and the ADS1015 is a 12-bit converter with a faster maximum rate. Both use I2C, have four inputs and a programmable gain amplifier. Choose by whether you need finer steps or more samples per second.

### Can I use the ADS1115 with an ESP32?

Yes, it connects over I2C like any other sensor. It is a common choice because some built-in ESP32 ADC pins are limited, and an external converter gives steadier readings. Power it from 3.3 V and keep the input voltage within the supply limit.

### Is the ADS1115 more accurate than the Arduino ADC?

It reports finer steps, for example 0.125 mV against 4.88 mV on a 5 V Uno, and it has a stable internal reference. But overall accuracy also depends on the sensor, wiring and noise, so check by comparing against a multimeter.

## Related reading

- [Robot battery runtime calculator](https://roboticsengineering.in/robot-battery-runtime-calculator/) to turn a measured voltage and current into runtime.
- [Ohm’s law and power calculator](https://roboticsengineering.in/ohms-law-power-calculator/) for checking divider and shunt values.
- [How to power a robot](https://roboticsengineering.in/how-to-power-a-robot/) for keeping analogue readings clean when motors run.

## About the author and how this is kept accurate

Written, checked and maintained by [Jignesh Panchal](https://www.linkedin.com/in/jignesh-s-panchal/) of [Jaadu Digital](https://jaadudigital.com/). Figures in worked examples come from the stated assumptions, not from a bench test of our own. Read the [editorial standard](https://roboticsengineering.in/editorial-standard/), follow the author on [LinkedIn](https://www.linkedin.com/in/jignesh-s-panchal/), or [send a correction](https://roboticsengineering.in/contact/). Last reviewed: November 2026.
