# UPS for a Robot Controller: Sizing and Buying Checks

> How to size a UPS for a robot controller, with a worked watts, VA and runtime example and checks on battery, waveform and signalling.

Canonical: https://roboticsengineering.in/ups-robot-controller-sizing/ | Published: 2026-11-15 | Updated: 2026-11-15 | Author: Jignesh S Panchal

**To size a UPS for a robot controller, add up the real load in watts, add a margin, convert to VA using the UPS power factor, then check the battery gives enough minutes for a controlled shutdown. The goal is usually a safe stop and save, not running production through an outage.**

## Key takeaways

- A UPS (uninterruptible power supply) keeps equipment running from a battery for a short time when mains power fails.
- UPS size is quoted in VA, but the real limit is also the watt rating; watts equal VA times the power factor.
- Runtime equals usable battery energy in watt-hours divided by the load in watts.
- For a robot controller, a few minutes for a safe stop and save is often the target; check what your robot maker requires.

## Load Power Estimate

Load power is how many watts the equipment connected to the UPS actually draws. Start from nameplates, then check with a measurement if you can.

- List what must stay up: robot controller, PLC, HMI or teach pendant link, network switch and any vision or safety controller.
- Read each nameplate or datasheet for input power. Nameplate numbers are usually maximums, so real draw can be lower.
- Do not put the robot’s servo drives on a small UPS unless the maker says so; motor power surges can be large. Many sites keep the UPS on the controller electronics only.
- Add a margin for growth, such as 25 percent.

Worked example with assumed values: robot controller 350 W plus PLC, HMI and switch 50 W gives 400 W. Add a 25 percent margin: 400 times 1.25 equals 500 W design load. The Indian power setting matters here: the [robot energy consumption in India](https://roboticsengineering.in/robot-energy-consumption-india/) article helps you estimate draw for your own cell.

## UPS Runtime Calculation for a Robot Controller

Runtime is how long the battery can carry the load. It equals usable battery energy divided by the load power.

Step 1: VA needed. Watts equal VA times power factor, so VA equals watts divided by power factor. Assume a UPS power factor of 0.7 (check your unit; some state 0.9 or 1.0). Then 500 divided by 0.7 equals 714.3 VA. Choose a UPS whose VA and watt ratings both exceed the load; a 1000 VA unit rated for at least 500 W would pass, if the datasheet confirms it.

Step 2: battery energy. Assume a 24 V battery string of 9 Ah. Energy equals voltage times amp-hours: 24 times 9 equals 216 Wh.

Step 3: usable energy. Assume you use 80 percent of the battery (depth of discharge) and the inverter is 85 percent efficient. Usable output energy is 216 times 0.8 times 0.85. First 216 times 0.8 equals 172.8. Then 172.8 times 0.85 equals 146.88 Wh.

Step 4: runtime. At 400 W: 146.88 divided by 400 equals 0.3672 hours, and times 60 gives 22.0 minutes. At the 500 W design load: 146.88 divided by 500 equals 0.29376 hours, which is 17.6 minutes.

| Quantity | Assumption or result |
| --- | --- |
| Load | 400 W, design 500 W |
| UPS power factor | 0.7 (assumed) |
| VA required | 714.3 VA |
| Battery | 24 V, 9 Ah = 216 Wh |
| Usable output energy | 146.88 Wh |
| Runtime at 400 W | about 22.0 min |
| Runtime at 500 W | about 17.6 min |

Now check against the need. Suppose the robot needs 5 minutes to stop and save. Energy at the output is 400 W times 5 divided by 60 hours, which is 33.33 Wh. Add an ageing allowance of 0.8 for an older battery. Nominal battery energy needed is 33.33 divided by (0.85 times 0.8 times 0.8). The product 0.85 times 0.8 is 0.68, and 0.68 times 0.8 is 0.544. So 33.33 divided by 0.544 is about 61.3 Wh. The 216 Wh battery has plenty of margin on paper. Real batteries deliver less at high discharge rates, so confirm with the maker’s runtime table. You can cross-check with the [robot battery runtime calculator](https://roboticsengineering.in/robot-battery-runtime-calculator/) and the general method in the [robot battery sizing calculation](https://roboticsengineering.in/robot-battery-sizing-calculation/).

## Battery Type

Battery type means the cell chemistry inside the UPS. The two common ones are sealed lead-acid and lithium iron phosphate (LiFePO4).

- Sealed lead-acid (VRLA) is common and familiar, but its life drops in heat and it is heavy. Indian summer panel temperatures shorten its life, so check the datasheet’s design life at your temperature.
- Lithium iron phosphate usually offers longer life and lighter weight, but check the built-in battery management and the maker’s support terms.
- Check battery replacement: can you swap cells without sending the UPS away?
- Plan a replacement cycle, since batteries age even when unused.

Battery safety matters, so read the [battery management system for robotics](https://roboticsengineering.in/battery-management-system-robotics/) explainer for why protection circuits exist. Follow the maker’s handling guidance; this is general guidance only.

## Output Waveform

Output waveform is the shape of the AC voltage the UPS gives while on battery. It can be a pure sine wave or a simulated (stepped) sine wave.

- Pure sine wave output is the safer choice for electronics with switch-mode power supplies, and for anything the equipment maker flags as sensitive.
- Stepped or modified sine output may upset some power supplies or cause humming or heat.
- Check the controller’s manual for any waveform requirement.
- Online (double conversion) UPS units give a clean output at all times; line-interactive and offline types switch over when mains fails. Compare transfer times in the datasheet against the controller’s tolerance.

## Shutdown Signalling

Shutdown signalling is how the UPS tells the controller that mains has failed and the battery is running down. Without it, the battery simply runs flat.

- Look for a dry-contact relay output, a USB or serial link, or a network card.
- Wire the “on battery” or “low battery” contact to a PLC input so the program can stop the robot and save data.
- Decide in advance what happens: finish the cycle, park the robot, then shut down.
- Do not rely on the UPS alone for safety functions. Emergency stops and safety circuits follow their own rules.

A site-level look at power quality is part of the [robot cell site readiness guide](https://roboticsengineering.in/robot-cell-site-readiness-india/).

## Testing the Unit

Testing the unit means proving, with the real load, that it holds up and signals correctly. Do it at commissioning and then at regular intervals.

Simulate a mains failure by switching the UPS input off in a controlled way, with the cell in a safe state, and watch the controller keep running and the signal reach the PLC. Time how long the load survives, and compare with your calculation. Repeat after battery replacement. The [robot cell commissioning checklist](https://roboticsengineering.in/robot-cell-commissioning-checklist/) is a good place to record this test.

## How to check this yourself

1. List each device on the UPS and write its nameplate watts; if you can, measure real draw with a plug-in power meter, using a qualified person for any panel work.
2. Add the loads, add your margin, then divide by the UPS power factor to get VA and compare with both the VA and watt ratings.
3. Compute runtime as battery watt-hours times depth of discharge times efficiency, divided by load watts.
4. Compare the result with the shutdown time your robot needs, and read the maker’s runtime table for your load.
5. Run a controlled outage test with the real load and record the time and the signal.

## Common mistakes

- Sizing in VA alone and ignoring the watt rating.
- Putting servo drives on a small UPS without checking surge demand.
- Using the battery’s full capacity in the runtime sum.
- Forgetting that old batteries hold less energy.
- Never testing shutdown signalling until a real outage.

## Quick checklist

- Load listed in watts with a margin.
- VA and watt rating both above the load.
- Runtime calculated and checked against the shutdown time.
- Waveform suits the controller and battery type suits the climate.
- On-battery signal wired to the PLC and tested.

## Frequently asked questions

### How do I convert watts to VA for a UPS?

Divide watts by the power factor. If the load is 500 W and the UPS power factor is 0.7, the VA needed is 500 divided by 0.7, about 714 VA. Always check both the VA and the watt rating on the datasheet, since the lower limit is the real one.

### How long will my UPS run my robot controller?

Runtime equals usable battery watt-hours divided by load watts. Usable energy is the battery energy times depth of discharge times inverter efficiency. A 216 Wh battery at 80 percent and 85 percent efficiency gives about 147 Wh, or about 22 minutes at 400 W. Check the maker’s runtime table.

### Do I need a pure sine wave UPS for an industrial controller?

Often it is the safer choice, since many controllers use switch-mode power supplies that may run hot or hum on stepped waveforms. Read the controller manual and the UPS datasheet. If either maker names a waveform requirement, follow it, and ask a qualified electrician for site wiring.

## Related reading

- [Battery voltage monitor with a divider](https://roboticsengineering.in/projects/battery-voltage-monitor-divider-arduino/), a build for watching battery level.
- [Robot battery current monitor with INA219](https://roboticsengineering.in/projects/robot-battery-current-monitor-ina219/), a build for seeing real current draw.
- [Ohm’s law and power calculator](https://roboticsengineering.in/ohms-law-power-calculator/), for quick watt and amp checks.
- [Industrial robotics hub](https://roboticsengineering.in/industry/), for related cell topics.
- [Series vs Parallel Battery Packs for Robots: Buying Checks](https://roboticsengineering.in/series-parallel-battery-pack-checklist/)

## About the author and how this is kept accurate

Written, checked and maintained by [Jignesh Panchal](https://www.linkedin.com/in/jignesh-s-panchal/) of [Jaadu Digital](https://jaadudigital.com/). Figures in worked examples come from the stated assumptions, not from a bench test of our own. Read the [editorial standard](https://roboticsengineering.in/editorial-standard/), follow the author on [LinkedIn](https://www.linkedin.com/in/jignesh-s-panchal/), or [send a correction](https://roboticsengineering.in/contact/). Last reviewed: November 2026.
