# Yaskawa Motoman Robot Alarm Codes \(DX200 & YRC1000\): Troubleshooting Chart

> Diagnose Yaskawa Motoman Alarm 1300, 1326 encoder battery, 4100 overload, 4110 shock sensor, 4315 collision, and 4980 home check faults.

Canonical: https://roboticsengineering.in/yaskawa-motoman-robot-fault-codes-troubleshooting/ | Published: 2026-11-20 | Updated: 2026-11-20

Yaskawa DX200 / YRC1000 · OEM Fault Hub

## Yaskawa Motoman Robot Alarm Codes (DX200 & YRC1000): Troubleshooting Chart

Search Motoman YRC1000 and DX200 alarm codes, shock sensor release, second home position verification, and SERVOPACK overload fixes.

Instant Filter (Code, Alarm Name, or Symptom)

Showing 10 of 10 Yaskawa OEM fault codes

Yaskawa · Alarm 1300 **CPU / Servo Communication Error**

Servo/Drive

**Root Cause:** Faulty servo pack link cable or EMI noise between YRC1000/DX200 main CPU and SERVOPACK.

**Recovery Steps:** Power cycle controller, inspect internal SERCOS/MECHATROLINK fiber/bus connectors, and verify grounding.

**Safety Interlock:** Check earth resistance (<100 ohm) in high-noise welding cells.

Yaskawa · Alarm 1326 **Encoder Battery Voltage Low**

Servo/Drive

**Root Cause:** Manipulator base encoder backup battery pack falling below minimum retention voltage.

**Recovery Steps:** Replace Yaskawa encoder battery pack while controller is powered ON, then clear alarm.

**Safety Interlock:** Powering down before replacement causes loss of home position.

Yaskawa · Alarm 4100 **Overload (Motor Thermal / Torque)**

Servo/Drive

**Root Cause:** Continuous RMS motor current exceeded servo pack thermal model due to excess payload or friction.

**Recovery Steps:** Verify payload weight & CoG settings, inspect reducer lubrication, and reduce duty cycle or speed.

**Safety Interlock:** Allow motor/drive to cool before restarting heavy cycle.

Yaskawa · Alarm 4110 **Shock Sensor / Collision Detected**

Motion/Collision

**Root Cause:** External shock sensor or software shock detection level tripped on sudden impact.

**Recovery Steps:** Switch to TEACH mode, release shock sensor reset, jog clear, and inspect torch/gripper alignment.

**Safety Interlock:** Re-verify TCP with pointer gauge after collision.

Yaskawa · Alarm 4207 **System Error (Servo Tracking)**

Motion/Collision

**Root Cause:** Following error exceeded limit during rapid acceleration or mechanical binding.

**Recovery Steps:** Inspect brake release supply, check axis interference, and verify payload inertia parameter.

**Safety Interlock:** Test motion at 25% teach speed before returning to PLAY.

Yaskawa · Alarm 4315 **Collision Detection (High Sensitivity)**

Motion/Collision

**Root Cause:** Software disturbance observer sensed unexpected resistance along programmed trajectory.

**Recovery Steps:** Inspect cable dress pack snagging, recalibrate tool weight/inertia, and tune shock level file.

**Safety Interlock:** Do not disable shock detection on unguarded cells.

Yaskawa · Alarm 4401 **Servo On Impossible (Safety Chain)**

Critical E-Stop

**Root Cause:** Dual-channel E-stop or safeguard circuit open when Servo On was requested.

**Recovery Steps:** Check pendant E-stop, external E-stop terminals, and safety relay board LEDs before pressing Servo On.

**Safety Interlock:** Inspect both A and B channels for single-channel weld faults.

Yaskawa · Alarm 4511 **Over Speed / Command Velocity Limit**

Servo/Drive

**Root Cause:** Commanded joint speed exceeded motor maximum RPM near wrist singularity.

**Recovery Steps:** Re-orient tool slightly away from A4/A6 collinear singularity or convert linear move to MOVJ.

**Safety Interlock:** Verify safe speed limit in Teach mode.

Yaskawa · Alarm 4980 **Out of Range (Home Position Check)**

Servo/Drive

**Root Cause:** Absolute encoder position differs from stored second home check position by more than tolerance.

**Recovery Steps:** Jog robot to alignment scribe marks, verify mechanical zero, and execute Second Home Position reset.

**Safety Interlock:** Never overwrite home position without verifying physical witness marks.

Yaskawa · Alarm 9000 **External User Alarm / PLC Hold**

Safety/I-O

**Root Cause:** User-defined ladder logic or external PLC raised an application fault (gripper timeout, part missing).

**Recovery Steps:** Inspect CIO ladder alarm description and field sensor (prox/vacuum switch) state on the fixture.

**Safety Interlock:** Check pneumatic pressure before resetting gripper fault.

### Yaskawa Second Home Position Check & Shock Sensor Reset

1. For Alarm 4110 (Shock Sensor), switch key to TEACH, press ALARM RESET, and check physical torch/EOAT alignment before clearing.
2. For Alarm 1326 (Encoder Battery Low), replace the manipulator base battery pack with the YRC1000/DX200 main breaker ON.
3. To resolve Alarm 4980 (Out of Range Home Position Check), jog all S/L/U/R/B/T axes to their physical alignment witness marks in JOINT mode.
4. Log in with Management security, open ROBOT -> HOME POSITION -> Check/Verify Second Home Position, and press MODIFY -> ENTER.

`<iframe src="https://roboticsengineering.in/yaskawa-motoman-robot-fault-codes-troubleshooting/" width="100%" height="780" style="border:1px solid #d6dfeb;border-radius:12px;" loading="lazy" title="Yaskawa Motoman Robot Alarm Codes (DX200 & YRC1000): Troubleshooting Chart"></iframe>`

**Grow Your Robotics / Automation Brand Online with Jaadu Digital** Technical SEO, B2B lead generation, and engineering content systems built for robotics integrators and OEMs.

[Explore Jaadu Digital →](https://jaadudigital.com/)

### Frequently Asked Engineering Questions

**How do I reset Yaskawa Alarm 4110 Shock Sensor without damaging the torch?**

Switch to TEACH mode, inspect whether the mechanical clutch or software shock detection tripped, jog slowly away from the workpiece, and re-check TCP against a gauge pointer.

**Why does Yaskawa Alarm 4511 Over Speed happen on linear moves?**

Linear MOVL trajectories passing near the R/B/T wrist singularity require extreme A4/A6 joint RPM. Re-orient the torch slightly or convert the transition segment to a MOVJ joint move.

**How do I clear Yaskawa Alarm 9000 External User Alarm?**

Alarm 9000 is raised by your cell PLC or CIO ladder logic (e.g., gripper feedback or part-present timeout). Inspect the CIO ladder alarm text and field sensors.

Multi-Currency · INR ₹ · USD $ · EUR €

## Cobot vs 6-Axis Industrial Robot ROI & Payback Calculator

Cobot Payback: 19.3 mo

Currency & Region Preset

Operators Replaced per Shift

Shifts per Day (1–3)

Fully Loaded Cost / Operator / Year

Cobot Cell Turnkey CapEx

6-Axis Industrial Cell CapEx (incl. Fencing)

Annual Throughput / Scrap-Reduction Value

6-Axis High-Speed Cycle Bonus (%)

Annual Maintenance & Power (% of CapEx)

Cobot Payback

19.3 mo

6-Axis Ind. Payback

43.5 mo

Cobot 5-Yr Net Gain

₹41,12,500

6-Axis 5-Yr Net Gain

₹16,62,500

**5-Year Cumulative Net Value Comparison**

Collaborative Robot (Cobot)₹41,12,500

6-Axis Industrial Robot Cell₹16,62,500

**Engineering Takeaway:** At 2 shifts/day, the Cobot achieves faster capital recovery due to lower safety guarding and integration overhead.

`<iframe src="https://roboticsengineering.in/cobot-vs-industrial-robot-roi-calculator/" width="100%" height="780" style="border:1px solid #d6dfeb;border-radius:12px;" loading="lazy" title="Cobot vs Industrial Robot ROI Calculator"></iframe>`

**Grow Your Robotics / Automation Brand Online with Jaadu Digital** Technical SEO, B2B lead generation, and engineering content systems built for robotics integrators and OEMs.

[Explore Jaadu Digital →](https://jaadudigital.com/)

### Frequently Asked Engineering Questions

**What is a realistic robotics ROI payback period in Indian manufacturing?**

On 2-shift CNC machine tending or palletizing, cobots typically pay back in 14–24 months while caged 6-axis industrial cells pay back in 24–42 months depending on throughput uplift.

**Why does a 6-axis industrial cell cost more up front than a cobot?**

Beyond the manipulator price, industrial cells require safety fencing, dual-channel light curtains, safety PLCs, heavier floor pedestals, and specialized integrator commissioning.

**When does a 6-axis industrial robot beat a cobot on 5-year ROI?**

When cycle times are aggressive (<5 s), payloads exceed 20–30 kg, or 24/7 3-shift operation amplifies the 25–45% throughput advantage of high-speed industrial arms.

**What annual OpEx percentage should be budgeted for robot cells?**

Budget 4–6% of total cell CapEx annually for grease/oil PM kits, gripper wear pads, vision lens cleaning, backup batteries, and electrical power (~0.6–2.5 kW average).

**How should fully loaded operator cost be calculated?**

Include base wages plus statutory benefits (PF/ESI/insurance), shift allowances, overtime, training, and attrition overhead rather than take-home pay alone.
