LiPo, Li-Ion & LiFePO4 Robot Battery Voltage-to-SOC Chart (1S–12S) & AWG Table
Interactive battery runtime, C-rate peak current, and wire-gauge sizing calculator paired with 1S–12S LiPo/Li-Ion/LiFePO4 SOC and silicone AWG tables.
Live Battery Runtime, C-Rate & Wire Gauge Calculator
1S–12S Robot Battery Voltage-to-SOC Chart
| Series | 100% Full | 80% | 50% Storage | 20% Alarm | 0% Load Cutoff |
|---|---|---|---|---|---|
| 1S | |||||
| 2S | |||||
| 3S | |||||
| 4S | |||||
| 5S | |||||
| 6S | |||||
| 7S | |||||
| 8S | |||||
| 10S | |||||
| 12S |
Silicone Wire AWG & Metric mm² Ampacity Table
| AWG Size | Cross-Section | Copper Dia (mm / in) | Continuous | 10s Burst | Resistance | Typical Robot Application |
|---|---|---|---|---|---|---|
| 22 AWG | 0.326 mm² | 0.64 mm (0.025 in) | 5 A | 8 A | 52.9 mΩ/m (16.1 mΩ/ft) | Logic / Sensor / Servo Signal |
| 18 AWG | 0.823 mm² | 1.02 mm (0.040 in) | 12 A | 18 A | 21.0 mΩ/m (6.4 mΩ/ft) | Small Stepper / 1A–8A Sub-Rail |
| 16 AWG | 1.31 mm² | 1.29 mm (0.051 in) | 18 A | 28 A | 13.2 mΩ/m (4.0 mΩ/ft) | Rover Logic + Light Actuator Bus |
| 14 AWG | 2.08 mm² | 1.63 mm (0.064 in) | 25 A | 40 A | 8.28 mΩ/m (2.5 mΩ/ft) | XT30 / Medium 15–25A Drive Bus |
| 12 AWG | 3.31 mm² | 2.05 mm (0.081 in) | 35–45 A | 65 A | 5.21 mΩ/m (1.6 mΩ/ft) | XT60 Main Pack Lead (3S–6S) |
| 10 AWG | 5.26 mm² | 2.59 mm (0.102 in) | 55–65 A | 95 A | 3.28 mΩ/m (1.0 mΩ/ft) | XT90 Combat / AMR Main Bus |
| 8 AWG | 8.37 mm² | 3.26 mm (0.128 in) | 80–90 A | 140 A | 2.06 mΩ/m (0.63 mΩ/ft) | AS150 / Heavy 48V AMR Bus |
| 6 AWG | 13.3 mm² | 4.12 mm (0.162 in) | 110–125 A | 200 A | 1.30 mΩ/m (0.40 mΩ/ft) | Forklift / High-Power Inverter Bus |
| 4 AWG | 21.2 mm² | 5.19 mm (0.204 in) | 150–170 A | 260 A | 0.81 mΩ/m (0.25 mΩ/ft) | Industrial AGV Main Battery Feed |
Frequently Asked Engineering Questions
What is the safe minimum discharge voltage for a LiPo robot battery under load?
Avoid discharging LiPo or Li-Ion cells below 3.3V per cell under load (3.5V resting) to prevent irreversible capacity loss; LiFePO4 packs can safely run down to 2.8V per cell under load.
How do I calculate continuous amps from mAh and C-rating?
Multiply capacity in Ah (mAh / 1000) by the continuous C-rating. For example, a 5000 mAh (5 Ah) 25C pack supports 5 x 25 = 125 A continuous, though keeping load under 70% improves cycle life.
What silicone wire AWG should I use for 30A, 60A, or 100A robot power buses?
Use 12 AWG (3.3 mm²) for up to 35-45A continuous, 10 AWG (5.3 mm²) for 55-65A, and 8 AWG (8.4 mm²) or 6 AWG (13.3 mm²) for 80-120A main motor buses with XT60/XT90/Anderson connectors.
DC Silicone Harness & Voltage Drop Check: A 6S LiPo pack sags fast enough under motor stall without losing another 1.5 V in undersized XT60 or Anderson leads. Before crimping battery leads, convert AWG to mm² and verify DC loop voltage drop at peak discharge amps on the EngiTech AWG to mm² Cable Size & Voltage Drop Calculator.