Pen Plotter Build: Motor and Belt Choices Before Buying

How to match steppers, GT2 belts, pulleys and drivers for a pen plotter, with a steps-per-mm worked example.

Reference
RE-4099
Published
Read
6 min

About the author · Editorial & verification standards

Partly assembled quadcopter frame with motors and flight controller on a workbench

For a pen plotter, pick NEMA 17 steppers with a driver such as the A4988, a GT2 belt with a 20-tooth pulley, and a stiff frame. This pen plotter motor belt buying guide shows how to match those parts and check the resolution before you order.

Key takeaways

  • A stepper motor with a 1.8 degree step takes 200 full steps per revolution.
  • Belt travel per revolution equals pulley teeth multiplied by belt pitch, so a 20-tooth pulley on a 2 mm pitch GT2 belt moves 40 mm per turn.
  • Microstepping smooths motion but does not give proportionally more torque or true accuracy.
  • A flexible frame ruins a plotter’s drawing quality no matter how good the motors are.

Stepper size and torque

A stepper motor is a motor that turns in fixed angle steps, and NEMA 17 names a common 42 mm square frame size. For a light pen carriage, NEMA 17 motors are normally enough.

MOTOR DRIVER & H-BRIDGE POWER ISOLATION SCHEMATICMCU Logic (3.3/5V)PWM + DIR / IN1-IN2H-Bridge Driver ICQ1–Q4 MOSFETs + FlybackDC / Stepper ActuatorInductive Load + Back-EMFBuck Regulator 5VLogic Supply + Star GNDVMOT Power Bus (12-24V)Bulk Cap 470uF + FuseCurrent Sense / ThermalVref Limit + Shutdown
Figure: H-Bridge motor driver stage showing PWM/DIR control, bulk capacitance on VMOT, flyback diodes, and star ground.

Check three datasheet values: rated current per phase, holding torque and winding resistance. A plotter moves only a pen and a small carriage, so you rarely need a larger motor, and our NEMA 17 vs NEMA 23 comparison explains when the bigger frame is worth it. Pick motors with a rated current your driver can supply, as covered in the stepper motor Arduino guide.

Belt type and pitch: a pen plotter motor belt buying guide

Pitch is the distance between belt teeth. GT2 belts with 2 mm pitch are a widely used choice on hobby plotters and printers, and they pair with GT2 pulleys.

BeltPitchNotes
GT22 mmCommon, many pulley options, quiet
HTD 3M3 mmCoarser teeth, different pulleys
MXL0.08 inchOlder style, check pulley match

Use a belt with steel or glass cord reinforcement for low stretch, and match belt width to the pulley (6 mm is a common listing). Never mix pitches: a GT2 belt on a different-pitch pulley will not mesh properly.

Pulley bore and teeth

Pulley bore is the hole diameter, and it must match the motor shaft. NEMA 17 shafts are commonly 5 mm, but check your motor’s datasheet, and buy pulleys with grub screws that bite on the shaft’s flat if it has one.

Tooth count sets resolution. Worked example, assuming a 1.8 degree motor, a 20-tooth GT2 pulley and a 1/16 microstep driver setting:

  1. Belt travel per revolution: 20 teeth x 2 mm = 40 mm.
  2. Full steps per revolution: 360 / 1.8 = 200.
  3. Travel per full step: 40 / 200 = 0.2 mm.
  4. Microsteps per revolution at 1/16: 200 x 16 = 3200.
  5. Travel per microstep: 40 / 3200 = 0.0125 mm.

The stepper step frequency calculator shows the pulse rate a given speed needs. Remember that a microstep of 0.0125 mm is a command resolution, not a promise of that accuracy, since belt stretch, backlash and frame flex are larger.

Driver choice

A stepper driver converts step and direction pulses into coil currents. The A4988 is a common, low-cost choice for plotters and is described on our A4988 stepper driver component page.

Check the driver’s supply voltage range, maximum current per phase, microstep options and whether it needs a heat sink. Set the current limit with the potentiometer using the reference-voltage formula from your module’s datasheet, because modules vary in sense resistor value. Put a capacitor across the motor supply as recommended by the driver maker, and do not connect or disconnect a motor while powered, which can damage the driver. For wiring checks, the wiring checker flags pin conflicts on Arduino boards.

Frame stiffness

Stiffness is how little the frame bends under load. A plotter’s lines wobble if rails flex or the carriage rocks, even with perfect electronics.

Check rail type (smooth rod with linear bearings or aluminium extrusion with wheels), whether the two axes stay square, and whether the belts can be tensioned. Belts should be taut enough to avoid sagging but not so tight that they load the motor bearings. Printed parts should use sensible wall thickness; see 3D printed robot parts design for guidance on strength.

Test plan

A test plan is a repeatable set of drawings that expose faults. Draw a square, a circle and a set of diagonal lines at one size, and compare corners and closure.

If the pen does not return to its start point, suspect lost steps; our missing steps fix guide lists the usual causes. Practice with the motorised camera slider project, which uses the same NEMA 17 and A4988 pair, or start smaller with the stepper turntable project. More build ideas are in the build hub.

How to check this yourself

  1. Read your motor datasheet for step angle, rated current and shaft diameter.
  2. Compute belt travel per step with teeth x pitch / steps per revolution.
  3. Mark a start position, command a known distance such as 100 mm, and measure what the carriage actually moved.
  4. Draw a closed square and check the end point returns to the start.
  5. Press on the carriage by hand while powered off and look for play in the rails.

Common mistakes

  • Choosing a pulley bore that does not match the shaft.
  • Mixing GT2 belts with different-pitch pulleys.
  • Setting the driver current without checking the module’s sense resistor.
  • Believing microstepping gives accuracy equal to its resolution.
  • Building on a flexible frame and blaming the firmware.

Frequently asked questions

Which stepper motor is enough for a pen plotter?

A NEMA 17 motor is normally enough for a light pen carriage. Check its rated current against your driver and read the holding torque on the datasheet. A larger frame such as NEMA 23 is rarely needed unless you carry a heavy tool.

How do I calculate plotter steps per mm?

Divide the motor’s steps per revolution, times the microstep setting, by the belt travel per revolution. With 200 steps, 1/16 microstepping and 40 mm per turn (20 teeth, 2 mm pitch), you get 3200 / 40 = 80 steps per mm.

Is GT2 belt good for a plotter?

GT2 is a common choice because pulleys and belts are easy to find in India and it runs quietly. Buy a reinforced belt, keep it tensioned and make sure the pulley pitch matches. Check the listing for belt width and material.

Quick checklist

  • Motor current and shaft diameter noted from the datasheet.
  • Belt pitch and pulley match confirmed.
  • Steps per mm calculated.
  • Driver current limit set with the correct formula.
  • Frame checked for flex before first drawing.

About the author and how this is kept accurate

Written, checked and maintained by Jignesh Panchal of Jaadu Digital. Figures in worked examples come from the stated assumptions, not from a bench test of our own. Read the editorial standard, follow the author on LinkedIn, or send a correction. Last reviewed: November 2026.

Pass it onWhatsAppLinkedIn

Keep reading

Continue learning

Free: the final-year project pack

A shortlist with BOMs, a report outline that matches the usual chapter scheme, a costing sheet and 40 viva questions. Built for the February–April submission season.

The Build Note

One short email when something is worth your bench time.

A new build sheet, a part price that moved, or a mistake worth avoiding. No daily drip, no recycled news.

One short email when a build or a price is worth your time. Unsubscribe in one click.